530b6aa5ec
The listing was narrowed by the provider record's enumerated models, which is the right bound only while one policy reaches a provider. Where two teams share a provider under different allowlists, every caller was offered the union: each model outside their own policy is a request the guardrail refuses a moment later, which is the empty-or-wrong picker this endpoint exists to avoid, moved one level up. A gateway record enumerating nothing was worse still — it offered the upstream's entire catalogue however narrow the policy. The synthesiser already knows which policies authorise a provider and which groups each binds, so the router can answer this at request time where it knows the caller's groups. Each route now carries one rule per authorising policy — its source groups and the models it permits — and the listing is bounded to the union across the rules matching the caller, intersected with what the provider serves. This is deliberately finer than the guardrail's own per-provider allowlist, which stays as it is: that list is a fail-closed backstop and cannot tell who is asking, so discovery is now narrower than the backstop rather than wider. A policy setting no allowlist lifts the restriction for the groups it binds, so nil and empty model lists stay distinct end to end — collapsing them would let a listing that should offer nothing fall open to everything.
Netbird Reverse Proxy
The NetBird Reverse Proxy is a separate service that can act as a public entrypoint to certain resources within a NetBird network. At a high level, the way that it operates is:
- Configured routes are communicated from the Management server to the proxy.
- For each route the proxy creates a NetBird connection to the NetBird Peer that hosts the resource.
- When traffic hits the proxy at the address and path configured for the proxied resource, the NetBird Proxy brings up a relevant authentication method for that resource.
- On successful authentication the proxy will forward traffic onwards to the NetBird Peer.
Proxy Authentication methods supported are:
- No authentication
- Oauth2/OIDC
- Emailed Magic Link
- Simple PIN
- HTTP Basic Auth Username and Password
Management Connection and Authentication
The Proxy communicates with the Management server over a gRPC connection. Proxies act as clients to the Management server, the following RPCs are used:
- Server-side streaming for proxied service updates.
- Client-side streaming for proxy logs.
To authenticate with the Management server, the proxy server uses Machine-to-Machine OAuth2. If you are using the embedded IdP //TODO: explain how to get credentials. Otherwise, create a new machine-to-machine profile in your IdP for proxy servers and set the relevant settings in the proxy's environment or flags (see below).
User Authentication
When a request hits the Proxy, it looks up the permitted authentication methods for the Host domain. If no authentication methods are registered for the Host domain, then no authentication will be applied (for fully public resources). If any authentication methods are registered for the Host domain, then the Proxy will first serve an authentication page allowing the user to select an authentication method (from the permitted methods) and enter the required information for that authentication method. If the user is successfully authenticated, their request will be forwarded through to the Proxy to be proxied to the relevant Peer. Successful authentication does not guarantee a successful forwarding of the request as there may be failures behind the Proxy, such as with Peer connectivity or the underlying resource.
TLS
Due to the authentication provided, the Proxy uses HTTPS for its endpoint, even if the underlying service is HTTP.
Certificate generation can either be via ACME (by default, using Let's Encrypt, but alternative ACME providers can be used) or through certificate files.
When not using ACME, the proxy server attempts to load a certificate and key from the files tls.crt and tls.key in a specified certificate directory.
When using ACME, the proxy server will store generated certificates in the specified certificate directory.
Auth UI
The authentication UI is a Vite + React application located in the web/ directory. It is embedded into the Go binary at build time.
To build the UI:
cd web
npm install
npm run build
For UI development with hot reload (served at http://localhost:3031):
npm run dev
The built assets in web/dist/ are embedded via //go:embed and served by the web.ServeHTTP handler.
Configuration
NetBird Proxy deployment configuration is via flags or environment variables, with flags taking precedence over the environment. The following deployment configuration is available:
| Flag | Env | Purpose | Default |
|---|---|---|---|
-debug |
NB_PROXY_DEBUG_LOGS |
Enable debug logging | false |
-mgmt |
NB_PROXY_MANAGEMENT_ADDRESS |
The address of the management server for the proxy to get configuration from. | "https://api.netbird.io:443" |
-addr |
NB_PROXY_ADDRESS |
The address that the reverse proxy will listen on. | ":443 |
-url |
NB_PROXY_URL |
The URL that the proxy will be reached at (where endpoints will be CNAMEd to). If unset, this will fall back to the proxy address. | "proxy.netbird.io" |
-cert-dir |
NB_PROXY_CERTIFICATE_DIRECTORY |
The location that certificates are stored in. | "./certs" |
-acme-certs |
NB_PROXY_ACME_CERTIFICATES |
Whether to use ACME to generate certificates. | false |
-acme-addr |
NB_PROXY_ACME_ADDRESS |
The HTTP address the proxy will listen on to respond to HTTP-01 ACME challenges | ":80" |
-acme-dir |
NB_PROXY_ACME_DIRECTORY |
The directory URL of the ACME server to be used | "https://acme-v02.api.letsencrypt.org/directory" |
-oidc-id |
NB_PROXY_OIDC_CLIENT_ID |
The OAuth2 Client ID for OIDC User Authentication | "netbird-proxy" |
-oidc-secret |
NB_PROXY_OIDC_CLIENT_SECRET |
The OAuth2 Client Secret for OIDC User Authentication | "" |
-oidc-endpoint |
NB_PROXY_OIDC_ENDPOINT |
The OAuth2 provider endpoint for OIDC User Authentication | "https://api.netbird.io/oauth2" |
-oidc-scopes |
NB_PROXY_OIDC_SCOPES |
The OAuth2 scopes for OIDC User Authentication, comma separated | "openid,profile,email" |