Detecting shutdown by inspecting the gRPC status code conflates a local
context cancellation with a server- or proxy-sent codes.Canceled. When
the latter occurs (e.g. an intermediary proxy resets the stream), the
retry loop silently terminates and the client never reconnects.
Switch to ctx.Err() in the signal Receive loop and management Sync/Job
handlers, and stop matching gRPC Canceled/DeadlineExceeded in the flow
client's isContextDone helper. With this change, a server-sent Canceled
is treated as a transient error and the backoff retry loop continues.
The Status recorder used to fire notifier callbacks while holding d.mux:
- notifyPeerListChanged / notifyPeerStateChangeListeners ran from inside
the locked section of every Update*/AddPeerStateRoute/etc.
- notifyAddressChanged ran from UpdateLocalPeerState and CleanLocalPeerState
while d.mux was held.
- onConnectionChanged was registered with a defer above defer d.mux.Unlock,
so it executed before the mutex was released in the Mark*Connected/
Disconnected helpers.
- notifyPeerStateChangeListeners did a blocking channel send under d.mux,
so a slow subscriber stalled every other d.mux holder.
A listener that re-enters the recorder (e.g. calls GetFullStatus from
within a callback) deadlocks against d.mux, and any callback that takes
longer than expected stalls every other state query for its duration.
Capture the values needed for notification under the lock, release d.mux,
then call the notifier. Build per-peer router-state snapshots inside the
lock and dispatch them via dispatchRouterPeers afterwards. The router-peer
channel send stays blocking, but now happens outside d.mux so a slow
consumer cannot stall any other d.mux holder, and no peer state
transitions are silently dropped.
The notifier itself is unchanged: its internal state was already protected
by its own locks, and the field d.notifier is set once in NewRecorder and
never reassigned, so reading it without d.mux is safe.
Also fix a pre-existing race in Test_notifier_RemoveListener /
Test_notifier_SetListener: setListener spawns a goroutine that writes
listener.peers, but the tests read listener.peers without waiting for it.
This change enables admins to configure posture checks for connecting public IPs of their peers.
It changes the behavior of the check as well and now the evaluation is if the received network is part of the configured network.
* enable pat creation on setup
* remove logic from handler towards setup service
* fix lint issue
* fix rollback on account id returning empty
* fix coderabbit comments
* fix setup PAT rollback behavior
* fix(client): enable UI autostart for silent and MSI installs
The MSI installer had no autostart logic and the EXE silent installer
skipped the autostart page, leaving the registry entry unwritten. This
caused the NetBird UI tray to not start at login after RMM deployments.
Add an AUTOSTART property (default: 1) to the MSI that writes the
HKLM Run key, and initialize AutostartEnabled in the NSIS .onInit so
silent installs match the interactive default.
* add real guid for NetBirdAutoStart component
* [relay] evict foreign client cache on disconnect
When a foreign relay's TCP connection drops, the manager's
onServerDisconnected handler only triggered reconnect logic for the
home server; the disconnected foreign entry stayed in the relayClients
cache. Subsequent OpenConn calls reused the closed client until the
60-second cleanup tick evicted it, breaking peer connectivity through
that relay for up to a minute.
Evict the foreign entry from the cache on disconnect so the next
OpenConn dials a fresh client.
Also:
- Make the reconnect backoff cap configurable via WithMaxBackoffInterval
ManagerOption; the previous hard-coded 60s constant forced
TestAutoReconnect to sleep ~61s. Test now polls Ready() and finishes
in ~2s.
- Add NB_HOME_RELAY_SERVERS env var that overrides the relay URL list
received from management, so a peer can be pinned to a specific home
relay (used by the netbird-conn-lab Edge 4 reproducer).
* [client] treat empty NB_HOME_RELAY_SERVERS as unset
Returning (urls=[], ok=true) when the env var contained only separators or
whitespace caused callers to wipe the mgmt-provided relay list, leaving the
peer with no relays. Treat a parsed-empty result the same as an unset env.
The JOB stream is a separate channel from the SYNC stream. Server-side
EOF or other transient errors on the JOB stream do not indicate that
the management connection is unhealthy — the SYNC stream remains the
authoritative state signal.
Previously, a JOB stream EOF would call notifyDisconnected and the
client would emit OnConnecting to the UI. The backoff retry would
reconnect the JOB stream, but handleJobStream never calls notifyConnected
on success, so the UI was stuck on "Connecting" until the next SYNC
event or health check.
Keep notifyDisconnected for codes.PermissionDenied since IsLoginRequired
relies on managementError to detect expired auth.
