The Status recorder used to fire notifier callbacks while holding d.mux:
- notifyPeerListChanged / notifyPeerStateChangeListeners ran from inside
the locked section of every Update*/AddPeerStateRoute/etc.
- notifyAddressChanged ran from UpdateLocalPeerState and CleanLocalPeerState
while d.mux was held.
- onConnectionChanged was registered with a defer above defer d.mux.Unlock,
so it executed before the mutex was released in the Mark*Connected/
Disconnected helpers.
- notifyPeerStateChangeListeners did a blocking channel send under d.mux,
so a slow subscriber stalled every other d.mux holder.
A listener that re-enters the recorder (e.g. calls GetFullStatus from
within a callback) deadlocks against d.mux, and any callback that takes
longer than expected stalls every other state query for its duration.
Capture the values needed for notification under the lock, release d.mux,
then call the notifier. Build per-peer router-state snapshots inside the
lock and dispatch them via dispatchRouterPeers afterwards. The router-peer
channel send stays blocking, but now happens outside d.mux so a slow
consumer cannot stall any other d.mux holder, and no peer state
transitions are silently dropped.
The notifier itself is unchanged: its internal state was already protected
by its own locks, and the field d.notifier is set once in NewRecorder and
never reassigned, so reading it without d.mux is safe.
Also fix a pre-existing race in Test_notifier_RemoveListener /
Test_notifier_SetListener: setListener spawns a goroutine that writes
listener.peers, but the tests read listener.peers without waiting for it.
* fix(client): enable UI autostart for silent and MSI installs
The MSI installer had no autostart logic and the EXE silent installer
skipped the autostart page, leaving the registry entry unwritten. This
caused the NetBird UI tray to not start at login after RMM deployments.
Add an AUTOSTART property (default: 1) to the MSI that writes the
HKLM Run key, and initialize AutostartEnabled in the NSIS .onInit so
silent installs match the interactive default.
* add real guid for NetBirdAutoStart component
* [relay] evict foreign client cache on disconnect
When a foreign relay's TCP connection drops, the manager's
onServerDisconnected handler only triggered reconnect logic for the
home server; the disconnected foreign entry stayed in the relayClients
cache. Subsequent OpenConn calls reused the closed client until the
60-second cleanup tick evicted it, breaking peer connectivity through
that relay for up to a minute.
Evict the foreign entry from the cache on disconnect so the next
OpenConn dials a fresh client.
Also:
- Make the reconnect backoff cap configurable via WithMaxBackoffInterval
ManagerOption; the previous hard-coded 60s constant forced
TestAutoReconnect to sleep ~61s. Test now polls Ready() and finishes
in ~2s.
- Add NB_HOME_RELAY_SERVERS env var that overrides the relay URL list
received from management, so a peer can be pinned to a specific home
relay (used by the netbird-conn-lab Edge 4 reproducer).
* [client] treat empty NB_HOME_RELAY_SERVERS as unset
Returning (urls=[], ok=true) when the env var contained only separators or
whitespace caused callers to wipe the mgmt-provided relay list, leaving the
peer with no relays. Treat a parsed-empty result the same as an unset env.
* [debug] fix port collision in TestUpload
TestUpload hardcoded :8080, so it failed deterministically when anything
was already on that port and collided across concurrent test runs.
Bind a :0 listener in the test to get a kernel-assigned free port, and
add Server.Serve so tests can hand the listener in without reaching
into unexported state.
* [debug] drop test-only Server.Serve, use SERVER_ADDRESS env
The previous commit added a Server.Serve method on the upload-server,
used only by TestUpload. That left production with an unused function.
Reserve an ephemeral loopback port in the test, release it, and pass
the address through SERVER_ADDRESS (which the server already reads).
A small wait helper ensures the server is accepting connections before
the upload runs, so the close/rebind gap does not cause a false failure.
The test writes 500 packets per family and asserted exact-count
delivery within a 5s window, even though its own comment says "Some
packet loss is acceptable for UDP". On FreeBSD/QEMU runners the writer
loops cannot always finish all 500 before the 5s deadline closes the
readers (we have seen 411/500 in CI).
The real assertion of this test is the routing check — IPv4 peer only
gets v4- packets, IPv6 peer only gets v6- packets — which remains
strict. Replace the exact-count assertions with a >=80% delivery
threshold so runner speed variance no longer causes false failures.
* [client] Suppress ICE signaling and periodic offers in force-relay mode
When NB_FORCE_RELAY is enabled, skip WorkerICE creation entirely,
suppress ICE credentials in offer/answer messages, disable the
periodic ICE candidate monitor, and fix isConnectedOnAllWay to
only check relay status so the guard stops sending unnecessary offers.
* [client] Dynamically suppress ICE based on remote peer's offer credentials
Track whether the remote peer includes ICE credentials in its
offers/answers. When remote stops sending ICE credentials, skip
ICE listener dispatch, suppress ICE credentials in responses, and
exclude ICE from the guard connectivity check. When remote resumes
sending ICE credentials, re-enable all ICE behavior.
* [client] Fix nil SessionID panic and force ICE teardown on relay-only transition
Fix nil pointer dereference in signalOfferAnswer when SessionID is nil
(relay-only offers). Close stale ICE agent immediately when remote peer
stops sending ICE credentials to avoid traffic black-hole during the
ICE disconnect timeout.
* [client] Add relay-only fallback check when ICE is unavailable
Ensure the relay connection is supported with the peer when ICE is disabled to prevent connectivity issues.
* [client] Add tri-state connection status to guard for smarter ICE retry (#5828)
* [client] Add tri-state connection status to guard for smarter ICE retry
Refactor isConnectedOnAllWay to return a ConnStatus enum (Connected,
Disconnected, PartiallyConnected) instead of a boolean. When relay is
up but ICE is not (PartiallyConnected), limit ICE offers to 3 retries
with exponential backoff then fall back to hourly attempts, reducing
unnecessary signaling traffic. Fully disconnected peers continue to
retry aggressively. External events (relay/ICE disconnect, signal/relay
reconnect) reset retry state to give ICE a fresh chance.
* [client] Clarify guard ICE retry state and trace log trigger
Split iceRetryState.attempt into shouldRetry (pure predicate) and
enterHourlyMode (explicit state transition) so the caller in
reconnectLoopWithRetry reads top-to-bottom. Restore the original
trace-log behavior in isConnectedOnAllWay so it only logs on full
disconnection, not on the new PartiallyConnected state.
* [client] Extract pure evalConnStatus and add unit tests
Split isConnectedOnAllWay into a thin method that snapshots state and
a pure evalConnStatus helper that takes a connStatusInputs struct, so
the tri-state decision logic can be exercised without constructing
full Worker or Handshaker objects. Add table-driven tests covering
force-relay, ICE-unavailable and fully-available code paths, plus
unit tests for iceRetryState budget/hourly transitions and reset.
* [client] Improve grammar in logs and refactor ICE credential checks
* fix(client): skip MAC address filter for network addresses on iOS
iOS does not expose hardware (MAC) addresses due to Apple's privacy
restrictions (since iOS 14), causing networkAddresses() to return an
empty list because all interfaces are filtered out by the HardwareAddr
check. Move networkAddresses() to platform-specific files so iOS can
skip this filter.
