* [client] Add WGConfigurer interface
To allow Rosenpass to work both with kernel
WireGuard via wgctrl (default behavior) and
userspace WireGuard via IPC on Android/iOS
using WGUSPConfigurer
* [client] Remove Rosenpass debug logs
* [client] Return simpler peer configuration in outputKey method
ConfigureDevice, the method previously used in
outputKey via wgClient to update the device's
properties, is now defined in the WGConfigurer
interface and implemented both in kernel_unix and
usp configurers.
PresharedKey datatype was also changed from
boolean to [32]byte to compare it
to the original NetBird PSK, so that Rosenpass
may replace it with its own when necessary.
* [client] Remove unused field
* [client] Replace usage of WGConfigurer
Replaced with preshared key setter interface,
which only defines a method to set / update the preshared key.
Logic has been migrated from rosenpass/netbird_handler to client/iface.
* [client] Use same default peer keepalive value when setting preshared keys
* [client] Store PresharedKeySetter iface in rosenpass manager
To avoid no-op if SetInterface is called before generateConfig
* [client] Add mutex usage in rosenpass netbird handler
* [client] change implementation setting Rosenpass preshared key
Instead of providing a method to configure a device (device/interface.go),
it forwards the new parameters to the configurer (either
kernel_unix.go / usp.go).
This removes dependency on reading FullStats, and makes use of a common
method (buildPresharedKeyConfig in configurer/common.go) to build a
minimal WG config that only sets/updates the PSK.
netbird_handler.go now keeps s list of initializedPeers to choose whether
to set the value of "UpdateOnly" when calling iface.SetPresharedKey.
* [client] Address possible race condition
Between outputKey calls and peer removal; it
checks again if the peer still exists in the
peers map before inserting it in the
initializedPeers map.
* [client] Add psk Rosenpass-initialized check
On client/internal/peer/conn.go, the presharedKey
function would always return the current key
set in wgConfig.presharedKey.
This would eventually overwrite a key set
by Rosenpass if the feature is active.
The purpose here is to set a handler that will
check if a given peer has its psk initialized
by Rosenpass to skip updating the psk
via updatePeer (since it calls presharedKey
method in conn.go).
* Add missing updateOnly flag setup for usp peers
* Change common.go buildPresharedKeyConfig signature
PeerKey datatype changed from string to
wgTypes.Key. Callers are responsible for parsing
a peer key with string datatype.
* When a peer disconnects, remove the endpoint address to avoid sending traffic to a non-existent address, but retain the status for the activity recorder.
This PR introduces a new inactivity package responsible for monitoring peer activity and notifying when peers become inactive.
Introduces a new Signal message type to close the peer connection after the idle timeout is reached.
Periodically checks the last activity of registered peers via a Bind interface.
Notifies via a channel when peers exceed a configurable inactivity threshold.
Default settings
DefaultInactivityThreshold is set to 15 minutes, with a minimum allowed threshold of 1 minute.
Limitations
This inactivity check does not support kernel WireGuard integration. In kernel–user space communication, the user space side will always be responsible for closing the connection.
With the lazy connection feature, the peer will connect to target peers on-demand. The trigger can be any IP traffic.
This feature can be enabled with the NB_ENABLE_EXPERIMENTAL_LAZY_CONN environment variable.
When the engine receives a network map, it binds a free UDP port for every remote peer, and the system configures WireGuard endpoints for these ports. When traffic appears on a UDP socket, the system removes this listener and starts the peer connection procedure immediately.
Key changes
Fix slow netbird status -d command
Move from engine.go file to conn_mgr.go the peer connection related code
Refactor the iface interface usage and moved interface file next to the engine code
Add new command line flag and UI option to enable feature
The peer.Conn struct is reusable after it has been closed.
Change connection states
Connection states
Idle: The peer is not attempting to establish a connection. This typically means it's in a lazy state or the remote peer is expired.
Connecting: The peer is actively trying to establish a connection. This occurs when the peer has entered an active state and is continuously attempting to reach the remote peer.
Connected: A successful peer-to-peer connection has been established and communication is active.
